SUMMIT mounting on elevator car frame crosshead beam RHP-X-OMS-560 load weighing device system
Elevator load weighing device system RHP-X-OMS-520
Description:
The elevator load weighing device HRP-X-OMS-520 is one kind of split type overload protection device for elevator overload detection and it is typically mounted one the the elevator lift car frame or beam, The strain gauge type pressure link load cell RHP-X typically works with the bending of elevator car steel frame and machine room steel crossbeams ,and it is also widely used for machines and vehicles force measures. The load weighing Sensor RHP-X measures the load applied on a steel frame by measuring the proportional flexion strain. Sensor designed for weighing depending on the deformations of steel beams in the motor bed frame or cabin frame.Easy to install and suitable for any type of beam.
Installation notice:
› The sensor must not be stressed mechanically before installation
› Install the sensor flat and without tension on the load bearing member
› Install the sensor using 4 bolts and securing nuts
› Use only the supplied bolts or bolts M6 type 8.8 and suitable nuts! Do not use spring or lock washers, only use flat washers!
› Tighten the screws with a maximum torque of 10Nm.
› The surface for mounting the load sensor must meet the following requirements: No welds in the sensor area
» Plane surface free of grease and paint without distortions or unevenness
Tenstion beam sensor RHP-X:
| Model |
RHP-X |
| Rated Load |
Undefined, works with bending steel frame |
| Sensitivity |
2.0+-0.02%mv/v |
| Total error |
+/-0.5% F.S |
| Excitation |
5-12V DC |
| Creep Error |
+/-0.02% F.S |
| Insulation Impedance |
≥5000 Ohm |
| T C SPAN |
+/-0.02% F.S./10 degree Celsius |
| Operation temperature range |
-30 to 70 degree Celsius |
| Input Resistance |
380+/-20 ohm |
| Output Resistance |
352+/-3 ohm |
| Construction |
Alloy Steel |
| Protection Class |
IP68 |
| Cable Length |
3M |
Elevator weighing control unit:OMS-560
| Control Unit:OMS-520 |
| Operation Voltage |
AC/DC18-45V |
| Nominal power |
4W |
| Load Cell Channel |
1 |
| Relay Number |
4(overload,full,half empty load ) |
| Contact Load |
1A125VAC,2A 30VDC,5A 250VAC/5A 30VDC |
| Display Type |
4 digits 0.56 inch LED |
| Display mode |
Weight/percentage |
| Key number |
6 |
| Voltage analog |
-10v-+10v, 0V-10V |
| Current analog |
4mA-20aA |
| Sensor operation voltage |
DC5V |
| Signal Hold Voltage |
AC/DC12-45V |
| Measuring precision |
0.1% |
| Operation temperature |
-45degree-+85degree |
| Size |
90x84x58mm |
| Weight |
265g |
Instllation&Wiring Diagram
LS-58S WDS-MR200 SLO-30V
WE UTEC could provide a wide range of elevator Load Weighing Control device system for versatile installation postion. methods like rope hitch installation, under car platform installation, crossbeam installation, clamping on traction rope installation in order to offer a safe and comfortable elevator running status.
Broad selection: Load weighing system in any location of elevator, Using SUMMIT solutions loads can be weighed in every imaginable situation.We offer you flexible, modular solutions for both requirements, and wide experience with modernization projects. we attention to detail in the design of their modular system allows great freedom to configure load weighing systems to suit all types of cabin.
Universal device for working with different load cells:
- Under Elevator cabin floors:UC-AP-OMS-560
- Clamping on wire rope:WDS series, RH-SM-OMS-820
- Machine bed frane:RHP-X-OMS-560
- Between the wire rope hitch plate:RHP-E-OMS-520
A solution providing very precise load weighing way, and Under cab sensors are not recommended for modernization. Simple solutions for modernization with no impact on the existing regulated travel parameters Very simple installation with no mechanical modification Cost-effective load weighing with a single sensor which can be scaled for a precise result
Elevator load weighing device system RHP-X-OMS-520
){kind=link}